Plumbing for Beginners: What You Need for Bathtub Installation
Plumbing for Beginners: What You Need for Bathtub Installation
Blog Article
We have come across this article on Installing A Bathtub down the page on the internet and believe it made perfect sense to discuss it with you here.
Setting up a bath tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is readily easily accessible, the task can move speedily; if you have to open a wall surface to remove the old bathtub and also position the new bathtub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. Ensure you have actually certified yourself for the task and fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This article will certainly aid you mount a brand-new bathtub in your shower room if you have already purchased a brand-new tub and do not need to alter the setup of your previous supply of water pipelines.
Your tools and also product list need to consist of the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing faucets can be quite bothersome due to the restricted gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Protect the tap in place with the maker supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal tap ports. The previous kind ought to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Using both wooden boards under its feet, position the bathtub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water and check all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub as well as additionally inspect the overflow electrical outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the tub should wait up until the bath tub has actually been made use of a minimum of when as this will settle it into its last position.
Preparing for the Installment
First of all, the sustaining structure supplied with the bath should be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid stress on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final position.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, bring about issues with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components as well as installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily available on the market. It is suggested to fit the tiles utilizing waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that blog post on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Be sure to take a moment to share this write-up if you enjoyed reading it. Thank-you for going through it.
Hot water gone? Call. Report this page